Benefits
-
High-temperature process resistance: Suitable for selected solder reflow and other elevated-temperature manufacturing processes.
-
Reduced silicone contamination risk: The non-silicone adhesive system is beneficial for applications sensitive to silicone residue.
-
Clean removal: Helps reduce adhesive residue on compatible substrates under specified processing conditions.
-
Improved handling: The PET release liner supports positioning, handling, and precision converting.
-
Component protection: Provides a thin masking layer for sensitive electronic parts and surfaces.
-
Converting flexibility: Can be evaluated for custom widths, sheets, and die-cut parts according to project requirements.
Technical Specifications
| Property | Typical specification |
|---|---|
| Product | 3M™ 7414L Polyimide Tape |
| Backing material | Polyimide film |
| Adhesive type | Specially designed acrylic pressure-sensitive adhesive |
| Adhesive system | Non-silicone |
| Color | Amber |
| Polyimide backing thickness | 25 μm |
| Adhesive thickness | 22 μm |
| Nominal tape thickness, excluding liner | Approximately 47 μm |
| PET release liner thickness | 50 μm |
| Nominal total construction thickness, including liner | Approximately 97 μm |
| Adhesion to stainless steel | Approximately 0.69 N/cm |
| Standard roll length | 33 m |
| High-temperature performance | 260°C for 30 minutes under specified test conditions |
| Continuous operating temperature | Do not infer from the short-duration process temperature; consult the applicable TDS |
Note: Values are typical or region-specific published data, not guaranteed specifications. Confirm the current technical data sheet for the exact product and market before purchase or process qualification.
Applications
-
PCB reflow soldering masking
-
High-temperature masking of electronic components
-
Printed circuit board surface protection
-
Temporary component positioning during manufacturing
-
Sensor package protection
-
Protection of gold-plated and other residue-sensitive areas
-
Leadframe masking
-
Through-hole sealing in selected electronics processes
-
Temporary bonding during high-temperature processing
-
Precision die-cut masking components
Compatible Materials
Potential substrates include:
-
FR-4 printed circuit board surfaces
-
Polyimide film and components
-
Gold-plated electronic contact areas
-
Selected metal surfaces
-
Copper surfaces under validated process conditions
-
Suitable electronic packaging materials
-
Selected plastics used in electronic assemblies
Actual compatibility depends on the substrate, surface finish, temperature profile, exposure time, and removal procedure. Test the tape on the intended substrate before production use.
Industries
-
Electronics manufacturing
-
Printed circuit board assembly
-
Semiconductor and electronic packaging
-
Sensor manufacturing
-
Automotive electronics
-
Industrial electrical equipment
-
Precision electronic component manufacturing
-
High-temperature process manufacturing
Why Choose 3M 7414L Polyimide Tape?
3M 7414L combines a heat-resistant polyimide film with a specially designed non-silicone acrylic adhesive and a PET release liner. This construction is designed for masking and protecting sensitive electronic surfaces during high-temperature processes where clean removal is important.
The release liner can also make the material easier to handle during positioning, slitting, and die-cutting. For manufacturers requiring custom tape widths, sheet formats, or precision-cut components, Yousan can assess the feasibility of converting the material to meet specific application requirements.
Material suitability should be validated against the actual process temperature, substrate, and cleanliness requirements.
Installation Guide
-
Prepare the surface: Ensure the substrate is clean, dry, and free of oil, dust, and other contaminants.
-
Check the process conditions: Confirm the temperature profile, exposure duration, substrate compatibility, and removal requirements.
-
Position the tape: Remove or fold back the PET release liner as appropriate and apply the adhesive side to the intended area.
-
Apply uniform pressure: Ensure good contact without wrinkles, stretching, or trapped air.
-
Run the validated process: Use the tape within the tested thermal and process conditions.
-
Remove carefully: Follow the validated cooling and removal procedure to minimize residue or surface damage.
-
Inspect the surface: Verify cleanliness and component condition after removal.
Always qualify the tape under actual production conditions before full-scale implementation.
Storage
-
Store in the original packaging in a clean, dry environment.
-
Avoid direct sunlight, excessive heat, moisture, and dust.
-
Keep the adhesive surface free from contamination.
-
Protect the release liner from creasing, tearing, or contamination.
-
Follow the manufacturer’s storage and shelf-life recommendations in the current technical documentation.
FAQ
1. What is 3M 7414L polyimide tape used for?
It is designed for high-temperature masking, surface protection, and temporary bonding in electronics manufacturing, including selected PCB reflow soldering and component protection applications.
2. What is the difference between 3M 7414 and 3M 7414L?
The main difference is that 7414L includes a PET release liner, while standard 7414 does not. The liner can improve handling and support precision converting.
3. What adhesive does 3M 7414L use?
It uses a specially designed acrylic pressure-sensitive adhesive that does not use a silicone adhesive system.
4. What is the thickness of 3M 7414L?
The nominal polyimide backing is 25 μm and the adhesive is 22 μm, giving approximately 47 μm excluding the liner. The PET liner is approximately 50 μm thick.
5. Can 3M 7414L withstand 260°C?
3M documentation reports performance at 260°C for 30 minutes under specified conditions. This is a short-duration process rating, not a continuous operating-temperature rating.
6. Is 3M 7414L suitable for PCB reflow soldering?
It is designed for selected high-temperature masking and protection applications, including PCB solder reflow. Verify suitability against the actual process profile and substrate.
7. Does 3M 7414L leave adhesive residue?
It is designed for clean removal from suitable surfaces under specified conditions. Results depend on the substrate, temperature, exposure time, and removal procedure, so testing is recommended.
8. Can 3M 7414L be supplied in custom widths or die-cut shapes?
Custom slitting, sheets, or die-cut parts may be feasible, depending on material availability, dimensions, tolerances, and order quantity.
Downloads
Available upon request:
- 3M 7414L Polyimide Tape Technical Data Sheet (TDS)
- Safety Data Sheet (SDS)
- Product Brochure
- Die-Cutting Capability Guide
Please contact our sales team if you require the latest technical documentation.







